Pre Owned Meyers! 16 Milo 90's available and 4 Milo 120's. We have dollies and covers for these, give us a call for a package deal. The MILO high-power curvilinear array is remarkably compact and lightweight for a self-contained, four-way system — particularly considering that it delivers 140 dB SPL peak output with exceptionally flat phase and frequency response. MILO contains three dedicated very-high frequency transducers that extend its operating range to 18 kHz, increase available high frequency headroom, and result in extraordinary resolution of delicate transients, even in very long throw applications.
High-power output (140 dB SPL peak)
Muting and solo controls (optional)
Lightweight and a fully self-contained system
Stadiums, arenas, concert halls and theatres
Touring sound reinforcement
Operating Frequency Range: 60 Hz - 18 kHz
Frequency Response: 65 Hz - 17.5 kHz ±4 dB
Phase response: 750 Hz - 16 kHz ±30°
Maximum Peak SPL: 140 dB @ 1 m
Dynamic range: >110 dB
Horizontal coverage: 90°
Vertical coverage: Varies, depending on array length and configuration.
Acoustical crossover: 560 Hz, 4.2 kHz
Transducers: Low/Low-Mid Frequency
Two 12" cone drivers with neodymium magnets
Nominal impedance: 4 Ω
Voice coil size: 4"
Power-handling capability: 1200 W (AES) on REM
Transducers: Mid-High Frequency
One 4" compression driver
Nominal impedance: 8 Ω
Voice coil size: 4"
Diaphragm size: 4"
Exit size: 1.5"
Power handling capability: 250 W (AES) on REM
Transducers: Very-High Frequency
Three 2" compression drivers
Nominal impedance: 12 Ω
Voice coil size: 2"
Diaphragm size: 2"
Exit size: 0.75"
Power handling capability: 100 W (AES)on REM
Type: Differential, electronically balanced
Max.common mode range: ±15 V DC, clamped to earth for voltage transient protection
Connectors: Female XLR input and male XLR loop output or VEAM
Input impedance: 10 kΩ differential between pins 2 and 3
Wiring: Pin 1: Chassis/earth through 220 kΩ, 1000 pF, 15 V clamp network to provide virtual ground lift at audio frequencies
Pin 2: Signal +
Pin 3: Signal -
Case: Earth ground and chassis
DC Blocking: None on output, DC blocked through signal processing
CMRR: > 50 dB, typically 80 dB (50 Hz - 500 Hz)
Rf filter: Common mode 425 kHz, Differential mode 142 kHz
TIM filter: <80 kHz, integral to signal processing
Nominal input sensitivity: 0 dB V (1 V rms, 1.4 pk) continuous is typically the onset of TPL limiting for noise and music.
Input level: Audio source must be capable of producing a minimum of +20 dBV (10 V rms, 14 V pk) into 600Ω in order to produce maximum peak SPL over the operating bandwidth of the loudspeaker
Amplifier type: Complementary power MOSFET output stages (class AB/ H)
Output Power: 3935 W (Four channels: 3 x 1125 W, 1 x 560 W)
THD, IM TIM: <.02%
Load capacity: 4 Ω low, mid and very high channels; 8 Ω high channel
Cooling: Forced air cooking, 4 fans total (2 ultrahigh-speed reserve fans)
AC power connector: 250 V AC NEMA L6-20 (twist lock) inlet, IEC 309 male inlet or VEAM connector
Voltage Selection: Automatic, two ranges, each with high-low voltage tap
Safety Agency Rated Operating voltage: 95 V AC – 125 V AC, 208 V AC - 235 V AC; 50/60 Hz
Turn-on and Turn-off Points: 85 V AC – 134 V AC; 165 V AC - 264 V AC
Idle Current: 1.1 A rms (115 V AC), 0.55 A rms (230 V AC), 1.3 A rms (100 V AC)
Max. Long-term Cont. Current Draw (>10 sec): 11.2 A RMS (115 V AC); 5.6 A RMS (230 V AC); 12.9 A RMS (100 V AC)
Burst Current (< 1 sec): 14.4 A rms (115 V AC), 7.2 A rms (230 V AC), 16.6 A rms (100 V AC)