Aviom Mix320-D Personal Mixing System

The Aviom Mix320-D Personal Mixing System has been designed specifically for use with Dante enabled consoles and networks. It includes everything you need to create a personal mixing system for six performers.

The Aviom Mix320-D Personal Mixers get their digital data and power over the same cable, so all you need to do is connect a Cat-5 cable and you’re ready to start using the system.

The Mix320-D Personal Mixing System makes it easy to add Aviom monitoring to a Dante-enabled mixing console or audio network. No analog input module or console card is required; inputs get patched directly from your Dante network.

The Mix320-D system includes a D400-Dante A-Net Distributor that allows up to 32 channels to be patched from the Dante network to the personal mixing system inputs. The D400-Dante is also used to supply A-Net digital data and DC power to the mixers. The Mix320-D system includes six A320 Personal Mixer for the performers, plus six MT-1a Mic Stand Mounts for attaching the A320 mixers to mic stands, as well as all the Cat-5e cables you’ll need to connect the products.

Intuitive Mixing

The A320 Personal Mixer gives performing and recording musicians simple, intuitive control over their monitor mixes. It features a 32-channel mix engine with 16 mono or stereo mix channels buttons and easy to use Stereo Placement controls.

Connect headphones, ear buds, or a wireless in-ear monitoring system to the Personal Mixer and you’re ready to start mixing.

Distribute Power and Audio Over Cat-5

For distributing the A-Net digital data and DC power to the A320 Personal Mixers, the system includes the D400-Dante A-Net Distributor.

The D400-Dante also serves as the system’s input device; it allows up to 32 channels from your Dante network to be assigned to the eight powered A-Net ports on its front panel. Stereo Link switches allow adjacent channels to be treated as a stereo pairs on the A320 Personal Mixers where they will appear on a single mix channel button.

System Options

The Mix320-D system uses a Dante network for its inputs. If you use a digital console, check out the Mix320-Y Personal Mixing System which includes a Y1 card for Yamaha consoles for its inputs. Or, if you have an analog console or recording system, the Mix320-A Personal Mixing System is what you need. It includes the 16-channel, line-level AN-16/i Input Module as its front end.

The mixing system packages are also easy to expand when you’re ready—just add more Personal Mixers and A-Net Distributors as needed.

Features:

• D400-Dante A-Net Distributor
• A320 Personal Mixers
• MT-1a Mic Stand Mounts
• Cat-5e cables

Includes:

• 1x AN-16/i v.2 Input Module
• 1x D400 A-Net Distributor
• 6x A320 Personal Mixers
• 6x MT-1a Mic Stand Mounts
• 7x Cat-5e cables

To learn more about Aviom, Click Here

View more products from Aviom

• Audio Output: 1/4" TRS stereo, headphone or line level
• Stereo Mix Output, Headphone/Line:
• Tip: Audio Left;
• Ring: Audio Right;
• Sleeve: Ground
• A-Net I/O:
• 1 A-Net In, RJ45 connector;
• Supports Pro16 and Pro16e
• D/A Conversion: 44.1/48kHz, 24-bit:
• Stereo Operation:
• Stereo Link, per channel pair;
• Set at the input module;
• Variable pan per mono channel or pan/spread per stereo channel pair
• Headphone Output: 275 mW per side into 50 Ohms (both sides driven)
• Output Impedance: 5 Ohms
• Freq. Response: 3Hz-22kHz +0.2dB/-3dB at 50 Ohms
• THD +N: < 0.003%
• Output Voltage for Personal Mixers: 24VDC, 0.5 amp
• Transmitted over the Cat-5e cable
• Signal to Noise (unweighted):
• -106dB (measured with zero data into all channels)
• Latency: 0.880 msec (measured from analog input to analog output)
• Pro16e A-Net:
• Use Cat-5e (or better) cable;
• Maximum 400 ft (122 m) between devices;
• Supports Power Over A-Net
• Cat-5 cable:
• Use shielded Cat-5e (or better) cable to stay below the CISPR 22
• Class B, ICES-003, and FCC 47 CFR Part 15 Class B emissions limits.
• Power:
• 24 VDC, 0.5 amp;
• Power is supplied over the Cat-5 cable when connected to an Aviom A-Net Distributor
• Dimensions: 10.26" (260.6 mm) wide x 6.14" (155.95 mm) deep x 1.91" (48.51 mm) high
• Weight: 1.3 lb. (0.59 kg)
• Options: MT-1a Mic Stand Mount
• Dante Interface: 32 channels (44.1/48kHz Sample Rate)
• Dante Primary I/O: RJ45 connector
• Dante Secondary I/O: RJ45 connector
• Dante LEDs: Network Activity (green);
• 1GB Network Connection Active (yellow)
• A-Net Out to Personal Mixers: Eight RJ45 connectors, powered
• A-Net Out: Pro16e A-Net; RJ45 connector, unpowered
• LEDs: Power On (red); Network Sync (green)
• Stereo Link: Two 8-position DIP switch blocks (1-16, 17-32)
• Output Voltage for Personal Mixers:
• 24VDC, 0.5 amp
• Transmitted over the Cat-5e cable
• A-Net Cables:
• Front Panel Connections: Shielded Cat-5e (or better) cable must be
• used to stay below the CISPR 22 Class B, ICES-003, and FCC 47 CFR
• Part 15 Class B emissions limits.
• Unshielded Cat-5e cable may be used on all rear panel connections
• Power Supply: Internal, IEC connector
• Input Voltage: 100-120 VAC or 200-240 VAC (with selector switch); 50-60Hz @220 W max
• AC Fuse Types:
• 115V range: T2.5AL/250V
• 230V range: T1.25AL/250V
• Dimensions: 19" (482.6 mm) wide x 7.386" (187.6 mm) deep; 2U, 3.5" (88.9 mm) high
• Weight: 12.0 lbs (5.44 kg)